Drilling Rigs
  Hammers
  Truck Mounted Drilling Rigs
  Button Bits
  Backhoe Loaders
Versatile 400
  Self Propelled Skid Mounted Rig
  Pick-N-Carry Crane 5T
  Digging/Pole Erection Machine
  KLR Cluster Hammer
  Hand Pumps
  Mineral Water Units
  KLR Generators
  Route Map
   
 
Drilling Rigs
Truck Mounted Drilling Rigs - KLR Make, CDR 400 Core Drilling Rig
Technical Specifications

General
KLR Make, CDR 400 Core Drilling Rig, Top Drive all hydraulically Operated Truck mounted Drilling Rig is designed for Core drilling for Geo-technical investigation (Geological survey) applications.
Drilling Capacity
  Parameters
Core Drilling
(Wire line or conventional)		 SI FPS
B Wireline or Conventional 400 Mtrs 1300 Feet
N Wireline or Conventional 300 Mtrs 1000 Feet
H Wireline or Conventional 185 Mtrs 600 Feet
P Wireline or Conventional 100 Mtrs 328 Feet

Note: Under favorable Drilling conditions. MAST Sturdy structural Box type Mast of electrically welded construction, main members made out of heavy duty structural steel material reinforced with suitable cross members. So that it is strong enough to withstand the high drilling loads. The dumping arrangement shall be provided for drilling upto 45◦ angle.

Mast Length 10000 MM 393 (Inches)
Rotary Head travel 7000 MM 275 (Inches)
Centraliser Opening 203 MM 8 (Inches)
Raising & Lowering With Hydraulic cylinder

Rotary Head Heavy duty Hydraulically Driven Top Head Rotation Unit is provided with High & Low speeds given below. The Rotation head is provided with slide out or swing out arrangement.

SI FPS
Max. Speed I 700 rpm
Max. Torque at Speed-I 50 Kgf-m 360 Lb-ft
Max speed II 300 rpm
Max Torque at Speed II 145 Kgf-m 1050 Lb-ft

Feed System
Feed system is provided with adequate travel for handling drill pipes & Casing pipes upto 6 Mt. long. The feed system is actuated by a suitable hydraulic cylinder with wire rope and pulley arrangement. The feed system has the following capabilities:

Max. Pull back/Up Capacity 9000 Kgf 19836 lbs
Max. Pull Down Capacity 3300 Kgf 7200 lbs
Max. Pull Back/Up Speed 40 Mtr/ min 130 ft/min
Revving Ratio 1.3
No. of Cylinders 1 No.

The Feed system will be incorporated with Hold back arrangement to control and limit weight on bit, rapid and slow feed arrangement to suit the variable ground conditions.
Hydraulic System

Max. Operating pressure 210 kg/cm2
Hydraulic Tank capacity 550
Filtration (Nom.) Return Line 10 microns
Hydraulic Oil Cooler 120 GPM (Fin type Oil to Air)

Prime Mover
Truck mounted rig with power drawn from the Truck engine with suitable PTO arrangements Optional: Separate Deck engine can also be mounted for the power source as per the customer requirement.
Stabilizers (Jacks)
System consist of four hydraulic leveling jacks with Reverse flow restricted valves to ensure safe operation. Two numbers are at the front (operator side) the rig controlled by two separate valves and Two jacks at the rear side of the rig controlled by a single valve.

Type Hydraulic cylinder
No. of Jacks 4 Nos.

Wireline Hoist Capacity
A suitable main hoist of following capacities shall be provided, on top of the mast.

Max. Bare Drum Pull 1000 kgf 2204 lbs
Max. Speed 100 m/min 330 ft/min
Cable Size 6 mm dia. 0.23 Inches
Drive Hydraulic motor

Note
KLR Drilling Rigs can be supplied in custom-built models in various Configurations as indicated below, Mounting features to suit all special requirements and Teechnical specifications can be offered accordingly
CDR 800, capable of drilling upto 800 Meters both in wireline Q and conventional
CDR 1500, capable of drilling up to 1500 Meters both in wireline Q and conventional